Safety Footwear Features

 

 

Safety Footwear

Safety Footwear

Safety footwear is designed to protect the user from potential work hazards. There are different components that made up safety footwear. These components include safety toe guards, metatarsal guards, electrical hazard ratings, electro static dissipating ratings and the soles of the shoes.

The mission of the Occupational Safety and Health Administration (OHSA) is to save lives, prevent injuries and protect the health of America’s workers. OSHA believes that the employer shall ensure that each affected employee wears protective footwear when working in areas where there is a danger of foot injuries due to falling or rolling objects or objects piercing the sole. Such equipment shall comply with American National Standards Institute (ANSI), ANSI Z-41-1991, “American National Standard for Personal Protection-Protective Footwear” [62 FR 40141, July 15,1997]. To accomplish this, federal and state governments must work in partnership with the more than 100 million working men and women and their six and a half million employers who are covered by the Occupational Safety and Health Act of 1970.

Safety toe guards originated in safety boots in 1925 with the intention to ultimately reduce the danger of foot injuries. Since then, the American National Standards Institute has set standards for protective footwear. There are two basic requirements all safety footwear must include: impact and compression. According to the test results there are three classifications of each.

  • IMPACT: I/75, I/50, and I/30 are designations for test results done with a 50-pound weight dropped from a set height.
  • COMPRESSION: C/75, C/50, and C/30 are designations of test done compressing the safety toes at 2,500 pounds (for C/75), 1,750 pounds (C/50), and 1,000 pounds (C/30).

The toe must have a minimum clearance inside the toe area of the shoe of 16/32” for men’s footwear and 15/32” for women’s footwear after the tests are completed.

There are many types of safety toes, such as steel toe, composite toe, alloy toe and Timberland’s own Titan toe (made from titanium). While all allow for great protection, both steel toe and composite toe safety footwear are Working Person’s Store’s most popular routes of protection.

The following chart shows the ANSI standards:

Classification Compression Clearance Classification Impact Ft. Lbs. Clearance
75 75 1/2″ 75 2,500 1/2″
50 50 1/2″ 50 1,500 1/2″
30 30 1/2″ 30 1,000 1/2″

 

Metatarsal guards protect the upper foot and toe area from potential “drop” hazards. The metatarsal guards can be attached to safety shoes both internally and externally. Each foot contains 26 bones.  Most of those bones are found on the upper foot and are called the metatarsal bones, from which the name of this protective device originates. Keeping each and every bone protected is very important so one can work freely without pain or injury.

Electrical Hazard (EH) rated footwear is designated to protect the wearer against open circuits up to 600 volts. EH footwear* is great for employees working around a plant or factory, such as plant operation personal, are usually most susceptible to EH conditions. EH safety footwear construction consists of a heel and sole combination usually molded into one single piece to the upper boot without any nails or metal. EH ratings are Tested by an independent lab to be able to withstand applications of 14,000 volts (V) at 60 Hertz (Hz) for one minute, with leakage in excess of 3.0 milliamperes (mA). EH ratings can also protect the wearer against open circuits up to 600 V or less under dry conditions.

WARNING: EH non-conductive footwear is not to be worn near explosives or in other environments requiring conductive footwear.

Electro Static Discharge (ESD) is the shock that is felt when a person walks across a carpet and touches a door knob and a discharge of electricity occurs between that person and the door. That shock was actually a discharge of electricity in the range of 2,000 to 3,000 volts.  The shock voltage has to be at least 2,000 volts before the human body can feel it.  The reason the 2,000 volt ESD discharge does not kill someone is that the current is very low, but that same voltage can kill electronic components or possibly ignite volatile chemicals or explosives. To be marked as Electric Static Dissipating Footwear, a shoe must pass testing requirements established by ANSI.  ESD footwear* can be classified as SD Type I or SD Type II. Footwear with this designation prevents the build-up of static electricity.  This is done through the construction of the footwear with a special silver thread used to stitch the soles to the uppers or with carbon inserts in the sole or footbed. Static Dissipating (SD) Type I must offer electrical resistance between 1 mega ohm to 100 mega ohms

DEFINITION: ohm = unit of electrical resistance, defined as the resistance in a circuit in which a potential difference of one volt creates a current of one ampere; hence, 1 ohm equals 1 volt/ampere. The megaohm (1,000,000 ohms) and milliohm (.001 ohm) are units derived from the ohm.

Sole safety is measured in three ways; slip-resistance, wear and comfort.

Slip resistance ratings for footwear are determined by independent laboratories.  To determine slip-resistance*, the soles are tested under dry, wet, oily, and oily/wet conditions according to a uniform testing method (ASTM F 489 ASTM F1667) using American Olean red quarry tile for the test surface. The different methods of testing include: 0.05 grams (2 drops) of vegetable oil is used for oily testing, 25/millaliters of distilled water is added for wet testing, 0.2 grams (7 drops) of vegetable oil is used for oily testing and 25/millaliters of distilled water is added for oily/wet testing.

The wear of the safety shoes includes many different types of material used in the construction of a shoe sole, each offers a different benefit. The durability of a shoe sole is at the mercy of the use and the work environment. Always try to match the shoe to the type of work and the working conditions. Most of the safety boots sold today have passed slip-resistance and wear tests.

The comfort level of safety shoes includes different composites used to construct a shoe sole which all offer different comfort levels. Everyone has a different perception of comfort* and each foot has its own special requirements. Only the person wearing the shoe can determine the comfort level.

The previous information about safety toe guards, metatarsal guards, electrical hazard ratings, electro static dissipating ratings and the soles of the shoes is meant to inform and help protect workers. When workers know what kind of foot protection they need and why they need it, the overall work environment will be much safer for everyone. It is not the sole responsibility for the employee to find this information. Make sure your employers are keeping you informed on up-to-date information so you can have optimal foot protection when times call for such.

*Working with Working Person’s Store’s “Boot Finder” is very easy to do. Just click the features you want, such as EH, ESD, slip-resistance or comfort guarantee, and we will find boots which meet your needs. There are many other choices so you can find exactly what you are looking for. 

4 Responses to “Safety Footwear Features”

  1. Vern October 29, 2012 at 12:30 pm #

    Thank you, this information helped.

    • @WPSBusinessTeam October 29, 2012 at 12:38 pm #

      Glad to be of service! That is the point of our blog, to help our readers understand the importance of work safety and which workwear products may work best for them. Let us know if you have any other questions.

  2. Michael Carter September 24, 2014 at 5:23 pm #

    We currently have a town policy that requires employees to wear steel toe boots at all times. With that said our employer reimburses each employee up to a certain dollar amount each year for that foot wear. Recently I have had employees ask if they could by Composite Toe footwear instead of Steel toe footwear? Do you know if OSHA and/or ANSI standards approve of Composite toe safety shoes as an equal option to a steel toed shoe?

Leave a Reply:

Gravatar Image

Business Blogs - BlogCatalog Blog Directory

 
Get 10% Off At WorkingPerson.com!

Sign-up for our email newsletter now and instantly receive an exclusive discount code in your email inbox to save 10% OFF your first order!

Newsletter Subscribers Also Enjoy
  • Free Coupons & Gifts
  • Exclusive Member Discounts
  • New Product Announcements
  • Helpful Safety Tips
No Thanks